Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
| Topic / Topic starter | Replies | Last post | |
|---|---|---|---|
|
Hub Motor vs. Frame-mounted Motor with Chain Drive by xring » Wed, 07/09/2008 - 10:12 |
3 |
by LinkOfHyrule Wed, 07/09/2008 - 15:21 |
|
|
Holding Brushes Back During Reassembly? by MarxNutz » Mon, 03/22/2010 - 17:54 |
1 |
by strawhistle Mon, 03/22/2010 - 19:00 |
|
|
NEED 1 broken wavecrest tidalforce motor, will pay up to $100 Thanks by Pavel » Fri, 08/01/2008 - 11:53 |
2 |
by Pavel Mon, 03/29/2010 - 00:00 |
|
|
What makes the Xebra go? by masonsteele » Sat, 01/13/2007 - 14:00 |
4 |
by masonsteele Mon, 01/22/2007 - 18:26 |
|
|
Brushed motors wear down the battery??? by reikiman » Sun, 03/29/2009 - 16:28 |
0 |
by reikiman Sun, 03/29/2009 - 16:28 |
|
|
Opening and cleaning an EVT hub motor by reikiman » Sat, 01/13/2007 - 23:17 |
0 |
by reikiman Sat, 01/13/2007 - 23:17 |
|
|
What type of Motor? by fJones » Sun, 04/19/2009 - 02:59 |
1 |
by reikiman Sun, 04/19/2009 - 15:01 |
|
|
How much can I get from ....? by longtong3 » Mon, 01/28/2008 - 21:57 |
2 |
by longtong3 Tue, 01/29/2008 - 01:22 |
|
|
Motorcycle Hub/Wheel Motor Suggestions? by OdnsRvns » Sat, 09/18/2010 - 23:14 |
5 |
by reikiman Mon, 09/20/2010 - 18:33 |
|
|
Question for motor experts by Qmavam » Sun, 09/28/2008 - 07:42 |
0 |
by Qmavam Sun, 09/28/2008 - 07:42 |
|
|
HTD 5m steel pulley. by edirtbiker » Tue, 06/12/2007 - 11:20 |
13 |
by chas_stevenson Fri, 06/15/2007 - 16:58 |
|
|
Motor Help by TheJack » Wed, 09/09/2009 - 17:08 |
4 |
by reikiman Fri, 09/11/2009 - 10:34 |
|
|
Small brushless RC motors 6-7 kw peak! by andrew » Thu, 05/01/2008 - 19:45 |
6 |
by andrew Sun, 05/18/2008 - 18:30 |
|
|
How to put a dc speed control on my dc motor by topnotchone » Sat, 11/19/2011 - 13:02 |
1 |
by Spaceangel Tue, 02/07/2012 - 07:58 |
|
|
12 to 24 volts or more by e-volt » Tue, 12/02/2008 - 22:04 |
1 |
by colin9876 Fri, 01/09/2009 - 10:31 |
|
|
Solenoid problem by reikiman » Mon, 10/01/2007 - 18:06 |
5 |
by usatracy Wed, 02/06/2008 - 20:53 |
|
|
Bmc 400w/600w 24v motor (USPD, lashout, Currie, Synergy cycles) by Pacific Ave Cycles » Wed, 03/03/2010 - 00:05 |
0 |
by Pacific Ave Cycles Wed, 03/03/2010 - 00:05 |
|
|
Kollmorgen Hub Question by engr_scotty » Tue, 07/15/2008 - 16:59 |
0 |
by engr_scotty Tue, 07/15/2008 - 16:59 |
|
|
I need clarification re the sensor wires on a brushless DC motor and how to test them. by sapo » Fri, 04/23/2010 - 23:23 |
5 |
by sapo Mon, 04/26/2010 - 01:03 |
|
|
SOUPCAN MOTOR, 98% Efficient by SPARKY » Thu, 08/21/2008 - 12:26 |
2 |
by SPARKY Fri, 08/22/2008 - 12:13 |
|
|
I need a 12.5inch Brushless Hub Motor. Suggestions? by Tireiron55 » Wed, 08/27/2008 - 09:34 |
0 |
by Tireiron55 Wed, 08/27/2008 - 09:34 |
|
|
Etek back!? by andrew » Tue, 02/06/2007 - 15:56 |
3 |
by NickF23 Fri, 05/25/2007 - 12:38 |
|
|
Double Shaft Motor for electric skateboard by lehula » Mon, 05/11/2009 - 17:11 |
0 |
by lehula Mon, 05/11/2009 - 17:11 |
|
|
D.I.Y Gearbox by Mr. Sander » Wed, 02/20/2008 - 12:54 |
2 |
by andrew Sat, 02/23/2008 - 12:15 |
|
|
AC Powered Motor Controller for DC Motor? by muniorbust » Tue, 12/21/2010 - 09:46 |
9 |
by memojazz Fri, 02/25/2011 - 08:24 |
Log in to post new content in the forum.
Who's online
There is currently 1 user online.
- gln103
Who's new
- Skyhawk 57
- wild4
- justinsmith07
- Juli76
- xovacharging
Support V is for Voltage
