Electric vehicle motors (DC motors, AC motors, hub motors, etc)

Topic	Replies	Views	Created	Last reply
Unite MY1020 24v 500w	5	1279	by Dave-s 05/13/2008 - 04:59	by Ray_T 05/14/2008 - 12:16
Converting a generator to a motor	5	958	by motorbiketim 05/09/2008 - 12:52	by motorbiketim 05/11/2008 - 14:42
This Met motor vs. etek	22	3446	by john 04/17/2008 - 07:14	by john 05/03/2008 - 11:43
Etek-R Report-- "Deep Cycle" Testing and Review	3	1746	by Jeffkay 04/18/2008 - 21:27	by Jeffkay 04/19/2008 - 11:11
96 volt two perm 132 in series and parallel	5	1362	by 96vperm132 04/15/2008 - 14:22	by frodus 04/16/2008 - 10:54
can you run a perm 132 at 96 volts?	0	344	by 96vperm132 04/16/2008 - 08:34	n/a
Wire size for 1200W?	7	370	by mf70 03/21/2008 - 11:14	by LinkOfHyrule 03/22/2008 - 19:59
Zap Xebra motor	2	797	by johny b 03/17/2008 - 14:00	by LinkOfHyrule 03/17/2008 - 14:46
how about this motor?	7	705	by JCinStaunton 03/12/2008 - 06:28	by andrew 03/17/2008 - 08:30
How to read motor performance charts and graphs	5	1226	by Mik 03/12/2008 - 04:36	by frodus 03/17/2008 - 08:20
crystal power, so to speak	1	398	by JCinStaunton 03/15/2008 - 21:26	by LinkOfHyrule 03/16/2008 - 06:54
Would a "Harmonic drive" be an option to adapt electric motors to existing motor bike drive shafts?	5	398	by Mik 03/07/2008 - 23:21	by Mik 03/11/2008 - 02:04
Anyone know where to get an Etek for cheap?	6	1091	by LinkOfHyrule 10/26/2007 - 12:51	by blainefillingim 02/28/2008 - 20:29
Motor power output [Page 1, 2]	37	1049	by s8nsmum 02/15/2008 - 10:42	by jdh2550_1 02/27/2008 - 12:27
D.I.Y Gearbox	2	1096	by Mr. Sander 02/20/2008 - 12:54	by andrew 02/23/2008 - 12:15
Drill motors?	4	552	by huntercook 02/18/2008 - 10:02	by huntercook 02/18/2008 - 22:56
How to refurbish old motor.	7	1868	by Mr. Sander 12/03/2007 - 14:05	by usatracy 02/11/2008 - 21:07
Solenoid problem	8	510	by reikiman 10/01/2007 - 17:06	by usatracy 02/06/2008 - 20:53
For those of you who haven't seen...	4	757	by LinkOfHyrule 01/06/2008 - 14:53	by LinkOfHyrule 02/06/2008 - 19:07
How much can I get from ....?	2	316	by longtong3 01/28/2008 - 21:57	by longtong3 01/29/2008 - 01:22
Brush hub motor repair question	1	348	by Scottmagic 01/22/2008 - 01:19	by Fechter 01/22/2008 - 12:49
Idea for Motor intergrated into Bike Cranks	7	1394	by 7circle 01/04/2008 - 11:15	by 7circle 01/06/2008 - 05:25
ligthest regenerating hub motor	0	715	by Efried 12/26/2007 - 07:50	n/a
running 24v@36v?	6	1707	by rpmarco 07/27/2007 - 11:31	by Frying Pigeon 12/25/2007 - 21:37
24volt 400watt kollmorgan internal controller?	0	872	by karma 12/18/2007 - 04:24	n/a