Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Electric outboard motor converted to scooter power? by rch427 » Wed, 12/10/2008 - 15:14 |
0 |
by rch427 Wed, 12/10/2008 - 15:14 |
|
Help with this ebike hub motor by carlos1984 » Wed, 09/22/2021 - 17:24 |
2 |
by carlos1984 Thu, 09/23/2021 - 06:48 |
|
Bmc 400w/600w 24v motor (USPD, lashout, Currie, Synergy cycles) by Pacific Ave Cycles » Wed, 03/03/2010 - 00:05 |
4 |
by friedwires Tue, 04/13/2010 - 18:49 |
|
HAS anyone ever run a PMG 132 in reverse direction at full voltage? by getadirtbike » Thu, 05/24/2007 - 15:57 |
1 |
by Patrick Fri, 06/15/2007 - 23:03 |
|
can you run a perm 132 at 96 volts? by 96vperm132 » Wed, 04/16/2008 - 09:34 |
0 |
by 96vperm132 Wed, 04/16/2008 - 11:52 |
|
what is an etek brush card assembly by sawracer » Thu, 08/21/2008 - 17:43 |
2 |
by sawracer Fri, 08/22/2008 - 17:46 |
|
Electric motor suddenly reverses...HELP!!!! by Alex_Millwright » Fri, 08/20/2010 - 14:43 |
1 |
by reikiman Fri, 08/20/2010 - 14:56 |
|
small motors big controllers by mattchicken » Thu, 05/07/2009 - 15:12 |
0 |
by mattchicken Thu, 05/07/2009 - 15:12 |
|
etek by echuckj5 » Mon, 09/10/2007 - 19:15 |
7 |
by echuckj5 Wed, 07/30/2008 - 09:17 |
|
Hub Motor vs. Frame-mounted Motor with Chain Drive by xring » Wed, 07/09/2008 - 10:12 |
3 |
by LinkOfHyrule Wed, 07/09/2008 - 15:21 |
|
Brushed or Bushless by wavedog » Mon, 09/29/2008 - 20:05 |
3 |
by wavedog Tue, 09/30/2008 - 08:26 |
|
help choosing correct motor, battery, etc setup for 80lb scooter project by new2voltz » Wed, 09/21/2011 - 09:09 |
1 |
by CHL lithium battery Thu, 09/22/2011 - 01:08 |
|
new motors by tiberiusx » Sat, 09/12/2009 - 13:50 |
1 |
by tiberiusx Sat, 09/12/2009 - 14:50 |
|
What makes the Xebra go? by masonsteele » Sat, 01/13/2007 - 14:00 |
4 |
by masonsteele Mon, 01/22/2007 - 18:26 |
|
Opening and cleaning an EVT hub motor by reikiman » Sat, 01/13/2007 - 23:17 |
0 |
by reikiman Sat, 01/13/2007 - 23:17 |
|
How much can I get from ....? by longtong3 » Mon, 01/28/2008 - 21:57 |
2 |
by longtong3 Tue, 01/29/2008 - 01:22 |
|
Deciding on which Motor 24v ~ 48v 500 ~ 1000w unsure how to compare the graphs by MasterCATZ » Wed, 04/21/2010 - 02:02 |
1 |
by MasterCATZ Wed, 04/21/2010 - 02:09 |
|
Need help identifying a GE motor by captsomer » Tue, 01/06/2009 - 14:31 |
7 |
by frodus Mon, 01/12/2009 - 11:57 |
|
HTD 5m steel pulley. by edirtbiker » Tue, 06/12/2007 - 11:20 |
13 |
by chas_stevenson Fri, 06/15/2007 - 16:58 |
|
Small brushless RC motors 6-7 kw peak! by andrew » Thu, 05/01/2008 - 19:45 |
6 |
by andrew Sun, 05/18/2008 - 18:30 |
|
Can I hot wire directly to see if the motor is good? by 2 B theprince » Thu, 08/28/2008 - 08:52 |
4 |
by 2 B theprince Thu, 08/28/2008 - 14:10 |
|
Electric Hubcap Pancake Motor, Controller, Workshops by Craig C » Wed, 09/15/2010 - 18:48 |
0 |
by Craig C Wed, 09/15/2010 - 18:48 |
|
Does a Bigger Motor mean more speed??? by poolman10 » Sat, 05/23/2009 - 16:56 |
5 |
by poolman10 Sun, 05/24/2009 - 17:20 |
|
Solenoid problem by reikiman » Mon, 10/01/2007 - 18:06 |
5 |
by usatracy Wed, 02/06/2008 - 20:53 |
|
Kollmorgen Hub Question by engr_scotty » Tue, 07/15/2008 - 16:59 |
0 |
by engr_scotty Tue, 07/15/2008 - 16:59 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- Skyhawk 57
- wild4
- justinsmith07
- Juli76
- xovacharging