Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Physics Question--How to test a pm dc motor for its voltage and current by james joule » Wed, 07/01/2009 - 23:08 |
2 |
by marylandbob Tue, 11/17/2009 - 12:19 |
|
help choosing correct motor, battery, etc setup for 80lb scooter project by new2voltz » Wed, 09/21/2011 - 09:09 |
1 |
by CHL lithium battery Thu, 09/22/2011 - 01:08 |
|
why can't you run two AC motors off the same controller? by masonsteele » Wed, 01/24/2007 - 21:28 |
1 |
by rgx Thu, 01/25/2007 - 12:00 |
|
Newbie question about Motors and amps >>> by JDELUNA » Sat, 02/10/2007 - 20:27 |
6 |
by andrew Mon, 02/12/2007 - 10:56 |
|
Would a "Harmonic drive" be an option to adapt electric motors to existing motor bike drive shafts? by Mik » Fri, 03/07/2008 - 23:21 |
5 |
by Mik Tue, 03/11/2008 - 03:04 |
|
12 to 24 volts or more by e-volt » Tue, 12/02/2008 - 22:04 |
1 |
by colin9876 Fri, 01/09/2009 - 10:31 |
|
Bmc 400w/600w 24v motor (USPD, lashout, Currie, Synergy cycles) by Pacific Ave Cycles » Wed, 03/03/2010 - 00:05 |
0 |
by Pacific Ave Cycles Wed, 03/03/2010 - 00:05 |
|
Deciding on which Motor 24v ~ 48v 500 ~ 1000w unsure how to compare the graphs by MasterCATZ » Wed, 04/21/2010 - 02:02 |
1 |
by MasterCATZ Wed, 04/21/2010 - 02:09 |
|
Anyone had any experience with Unite Hub Motors? by Gman » Fri, 06/22/2007 - 23:01 |
0 |
by Gman Fri, 06/22/2007 - 23:01 |
|
SOUPCAN MOTOR, 98% Efficient by SPARKY » Thu, 08/21/2008 - 12:26 |
2 |
by SPARKY Fri, 08/22/2008 - 12:13 |
|
Currie Direct Drive by rkd718 » Fri, 05/16/2008 - 17:21 |
0 |
by rkd718 Fri, 05/16/2008 - 17:21 |
|
What type of Motor? by fJones » Sun, 04/19/2009 - 02:59 |
1 |
by reikiman Sun, 04/19/2009 - 15:01 |
|
Electric Hubcap Pancake Motor, Controller, Workshops by Craig C » Wed, 09/15/2010 - 18:48 |
0 |
by Craig C Wed, 09/15/2010 - 18:48 |
|
motor identification by dingobingo » Wed, 10/17/2007 - 08:24 |
0 |
by dingobingo Wed, 10/17/2007 - 08:24 |
|
Question for motor experts by Qmavam » Sun, 09/28/2008 - 07:42 |
0 |
by Qmavam Sun, 09/28/2008 - 07:42 |
|
Motor Help by TheJack » Wed, 09/09/2009 - 17:08 |
4 |
by reikiman Fri, 09/11/2009 - 10:34 |
|
Homemede variable reluctance motor. Also the 12 volt bike to end all 12 volt bikes by D-Skor » Sat, 11/19/2011 - 07:11 |
0 |
by D-Skor Sat, 11/19/2011 - 07:11 |
|
90 degree motor 12v by airman90 » Sat, 05/05/2012 - 11:44 |
5 |
by MEroller Tue, 05/08/2012 - 14:40 |
|
Running Etek CCW by andrew » Thu, 03/22/2007 - 16:47 |
6 |
by andrew Sun, 03/25/2007 - 15:07 |
|
crystal power, so to speak by JCinStaunton » Sat, 03/15/2008 - 22:26 |
1 |
by LinkOfHyrule Sun, 03/16/2008 - 07:54 |
|
Recommended controller for Brushed Manta Etek? by captsomer » Fri, 01/02/2009 - 11:29 |
1 |
by ruprek Sat, 01/03/2009 - 04:30 |
|
Motor mounts.. where to get them? by reikiman » Thu, 05/06/2010 - 08:15 |
3 |
by strawhistle Thu, 05/06/2010 - 13:02 |
|
What's a good hub motor bearing lubricant, White Lightning? by Gman » Thu, 07/12/2007 - 15:08 |
5 |
by Gman Fri, 07/13/2007 - 06:52 |
|
I need a 12.5inch Brushless Hub Motor. Suggestions? by Tireiron55 » Wed, 08/27/2008 - 09:34 |
0 |
by Tireiron55 Wed, 08/27/2008 - 09:34 |
|
A Newber needs help with New / Gift Kollmorgan hub motor by henrypaz » Sun, 06/15/2008 - 14:56 |
8 |
by LeftieBiker Fri, 09/16/2016 - 02:42 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- Skyhawk 57
- wild4
- justinsmith07
- Juli76
- xovacharging