Electric vehicle motors (DC motors, AC motors, hub motors, etc)

TopicRepliesCreatedLast replysort icon
Reversing direction of rotation of PMG 132 motors
0
by FastForward
05/29/2008 - 12:54
n/a
Small brushless RC motors 6-7 kw peak!
6
by andrew
05/01/2008 - 19:45
by andrew
05/18/2008 - 18:30
Neodymium swap in 400w kollmorgen motor?
0
by noobster
05/18/2008 - 17:37
n/a
Kollmorgen undervoltage cutoff? and how to bypass it?
2
by ejonesss
05/15/2008 - 03:24
by ejonesss
05/18/2008 - 04:38
Currie Direct Drive
0
by rkd718
05/16/2008 - 17:21
n/a
Unite MY1020 24v 500w
5
by Dave-s
05/13/2008 - 05:59
by Ray_T
05/14/2008 - 13:16
Converting a generator to a motor
5
by motorbiketim
05/09/2008 - 13:52
by motorbiketim
05/11/2008 - 15:42
More info about automotive alternator used as motor
7
by dabit
03/16/2008 - 02:31
by shroomer
05/07/2008 - 19:48
This Met motor vs. etek
22
by john
04/17/2008 - 08:14
by john
05/03/2008 - 12:43
Etek-R Report-- "Deep Cycle" Testing and Review
3
by Jeffkay
04/18/2008 - 22:27
by Jeffkay
04/19/2008 - 12:11
96 volt two perm 132 in series and parallel
5
by 96vperm132
04/15/2008 - 15:22
by frodus
04/16/2008 - 11:54
can you run a perm 132 at 96 volts?
0
by 96vperm132
04/16/2008 - 09:34
n/a
Wire size for 1200W?
7
by mf70
03/21/2008 - 12:14
by LinkOfHyrule
03/22/2008 - 20:59
Zap Xebra motor
2
by johny b
03/17/2008 - 15:00
by LinkOfHyrule
03/17/2008 - 15:46
how about this motor?
7
by JCinStaunton
03/12/2008 - 07:28
by andrew
03/17/2008 - 09:30
How to read motor performance charts and graphs
5
by Mik
03/12/2008 - 05:36
by frodus
03/17/2008 - 09:20
crystal power, so to speak
1
by JCinStaunton
03/15/2008 - 22:26
by LinkOfHyrule
03/16/2008 - 07:54
Would a "Harmonic drive" be an option to adapt electric motors to existing motor bike drive shafts?
5
by Mik
03/08/2008 - 00:21
by Mik
03/11/2008 - 03:04
Anyone know where to get an Etek for cheap?
6
by LinkOfHyrule
10/26/2007 - 13:51
by blainefillingim
02/28/2008 - 21:29
D.I.Y Gearbox
2
by Mr. Sander
02/20/2008 - 13:54
by andrew
02/23/2008 - 13:15
Drill motors?
4
by huntercook
02/18/2008 - 11:02
by huntercook
02/18/2008 - 23:56
Solenoid problem
5
by reikiman
10/01/2007 - 18:06
by usatracy
02/06/2008 - 21:53
For those of you who haven't seen...
4
by LinkOfHyrule
01/06/2008 - 15:53
by LinkOfHyrule
02/06/2008 - 20:07
How much can I get from ....?
2
by longtong3
01/28/2008 - 22:57
by longtong3
01/29/2008 - 02:22
Brush hub motor repair question
1
by Scottmagic
01/22/2008 - 02:19
by Fechter
01/22/2008 - 13:49
No New Posts
No New Posts
New Posts
New Posts
Hot Thread (No New)
Hot Thread (No New)
Hot Thread (New)
Hot Thread (New)
Sticky Thread
Sticky Thread
Locked Thread
Locked Thread
Syndicate content

Short URL

Customize This