Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
| Topic / Topic starter | Replies | Last post | |
|---|---|---|---|
|
UPDATE ------I rewound my first motor, it runs great. by paul scooter » Thu, 01/11/2007 - 08:10 |
5 |
by rgx Sun, 02/11/2007 - 19:05 |
|
|
24volt 400watt kollmorgan internal controller? by karma » Tue, 12/18/2007 - 04:24 |
0 |
by karma Tue, 12/18/2007 - 04:24 |
|
|
mars brushless vs brushed etek for an electric dirt bike by kp647 » Fri, 09/05/2008 - 04:20 |
6 |
by ruprek Wed, 10/01/2008 - 21:14 |
|
|
How difficult is it to rewind a 1-phase 115V motor to a higher voltage 3 phase motor by terramir » Tue, 06/02/2009 - 01:57 |
3 |
by james joule Fri, 08/21/2009 - 05:56 |
|
|
Holding Brushes Back During Reassembly? by MarxNutz » Mon, 03/22/2010 - 17:54 |
1 |
by strawhistle Mon, 03/22/2010 - 19:00 |
|
|
Sprocket Help by SHARKBITEATTACK » Wed, 04/25/2007 - 16:40 |
6 |
by Sturdly Fri, 05/25/2007 - 16:35 |
|
|
Which motor? by Carpstar » Sun, 03/30/2008 - 05:27 |
7 |
by apshamilton Thu, 08/06/2009 - 10:48 |
|
|
How does a brush DC motor stop? by noobster » Thu, 10/16/2008 - 03:46 |
3 |
by spinningmagnets Thu, 10/16/2008 - 20:34 |
|
|
manufacturers of motors by arlberg » Fri, 11/07/2008 - 02:45 |
7 |
by Cherry Chou Wed, 09/04/2013 - 23:59 |
|
|
Radical Enabling Technology: Drive/Braking/Suspension Module by designtech3000 » Fri, 01/01/2010 - 03:02 |
5 |
by designtech3000 Mon, 01/11/2010 - 23:50 |
|
|
Motorcycle Hub/Wheel Motor Suggestions? by OdnsRvns » Sat, 09/18/2010 - 23:14 |
5 |
by reikiman Mon, 09/20/2010 - 18:33 |
|
|
1 Hp Scott Motor by echuckj5 » Thu, 09/13/2007 - 21:44 |
28 |
by echuckj5 Sat, 10/06/2007 - 10:49 |
|
|
15 Electric Motorcycle LEMCO Motors by reikiman » Wed, 07/23/2008 - 07:44 |
0 |
by reikiman Wed, 07/23/2008 - 07:44 |
|
|
A few questions about large hub motors... by todayican » Thu, 07/10/2008 - 19:25 |
2 |
by Mik Fri, 07/11/2008 - 05:06 |
|
|
The most efficient Hub Motor by wheelie » Wed, 03/18/2009 - 20:25 |
1 |
by garygid Wed, 03/18/2009 - 23:23 |
|
|
How to put a dc speed control on my dc motor by topnotchone » Sat, 11/19/2011 - 13:02 |
1 |
by Spaceangel Tue, 02/07/2012 - 07:58 |
|
|
How to open a crystal hub motor by chas_stevenson » Sat, 01/13/2007 - 17:48 |
4 |
by Ypedal Mon, 01/15/2007 - 17:41 |
|
|
For those of you who haven't seen... by LinkOfHyrule » Sun, 01/06/2008 - 14:53 |
4 |
by LinkOfHyrule Wed, 02/06/2008 - 19:07 |
|
|
Motor voltage, current and watts. by deronmoped » Thu, 09/11/2008 - 23:17 |
7 |
by LinkOfHyrule Thu, 10/23/2008 - 15:48 |
|
|
Brushed DC Motor Dead-Short by Kevin_Glass » Wed, 06/17/2009 - 13:41 |
1 |
by james joule Fri, 08/21/2009 - 05:17 |
|
|
I need clarification re the sensor wires on a brushless DC motor and how to test them. by sapo » Fri, 04/23/2010 - 23:23 |
5 |
by sapo Mon, 04/26/2010 - 01:03 |
|
|
quandry-motor size by tortuga0303 » Sun, 06/10/2007 - 19:04 |
6 |
by MB-1-E Mon, 06/11/2007 - 17:10 |
|
|
This Met motor vs. etek by john » Thu, 04/17/2008 - 08:14 |
22 |
by john Sat, 05/03/2008 - 12:43 |
|
|
Converting a generator to a motor by motorbiketim » Fri, 05/09/2008 - 13:52 |
5 |
by motorbiketim Sun, 05/11/2008 - 15:42 |
|
|
How do I lay my mits on a Crystalyte motor and controller in Australia?? by wheelie » Sat, 11/15/2008 - 18:32 |
0 |
by wheelie Sat, 11/15/2008 - 18:32 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- Skyhawk 57
- wild4
- justinsmith07
- Juli76
- xovacharging
Support V is for Voltage
