Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Best motor for hill climbing with load by gwh68 » Fri, 05/08/2009 - 07:44 |
4 |
by gwh68 Sun, 05/10/2009 - 16:09 |
|
|
Drill Motor: An Option? by engr_scotty » Tue, 07/15/2008 - 09:21 |
4 |
by dogman Tue, 07/15/2008 - 11:37 |
|
|
Alternator Output Question by Rane » Thu, 08/28/2008 - 22:55 |
4 |
by LinkOfHyrule Fri, 08/29/2008 - 23:05 |
|
|
Wheel huntin'... by LinkOfHyrule » Wed, 11/28/2007 - 15:42 |
4 |
by LinkOfHyrule Fri, 11/30/2007 - 12:41 |
|
|
Guide me on selecting motor & controller by YUVARAJ » Fri, 03/20/2009 - 03:32 |
4 |
by dogman Sat, 03/21/2009 - 05:14 |
|
|
EnerTrac kit by reikiman » Fri, 07/24/2009 - 21:30 |
4 |
by markcycle Tue, 08/25/2009 - 06:40 |
|
|
Need the whole "Kit and Kaboodle" :-) by todayican » Mon, 06/30/2008 - 04:20 |
4 |
by todayican Mon, 06/30/2008 - 16:45 |
|
|
Linear actuator motor by countersunk » Mon, 02/15/2010 - 23:02 |
4 |
by countersunk Fri, 02/19/2010 - 00:57 |
|
|
How to open a crystal hub motor by chas_stevenson » Sat, 01/13/2007 - 17:48 |
4 |
by Ypedal Mon, 01/15/2007 - 17:41 |
|
|
For those of you who haven't seen... by LinkOfHyrule » Sun, 01/06/2008 - 14:53 |
4 |
by LinkOfHyrule Wed, 02/06/2008 - 19:07 |
|
|
Bmc 400w/600w 24v motor (USPD, lashout, Currie, Synergy cycles) by Pacific Ave Cycles » Wed, 03/03/2010 - 00:05 |
4 |
by friedwires Tue, 04/13/2010 - 18:49 |
|
|
Can I hot wire directly to see if the motor is good? by 2 B theprince » Thu, 08/28/2008 - 08:52 |
4 |
by 2 B theprince Thu, 08/28/2008 - 14:10 |
|
|
Solenoid problem by reikiman » Mon, 10/01/2007 - 18:06 |
5 |
by usatracy Wed, 02/06/2008 - 20:53 |
|
|
Motorcycle Hub/Wheel Motor Suggestions? by OdnsRvns » Sat, 09/18/2010 - 23:14 |
5 |
by reikiman Mon, 09/20/2010 - 18:33 |
|
|
I need clarification re the sensor wires on a brushless DC motor and how to test them. by sapo » Fri, 04/23/2010 - 23:23 |
5 |
by sapo Mon, 04/26/2010 - 01:03 |
|
|
96 volt two perm 132 in series and parallel by 96vperm132 » Tue, 04/15/2008 - 15:22 |
5 |
by frodus Wed, 04/16/2008 - 11:54 |
|
|
Motor theory, ac vs bldc by Ampy » Sun, 06/08/2014 - 07:56 |
5 |
by Yuan Zhen Tue, 08/05/2014 - 00:06 |
|
|
Unite MY1020 24v 500w by Dave-s » Tue, 05/13/2008 - 05:59 |
5 |
by Ray_T Wed, 05/14/2008 - 13:16 |
|
|
NuVinci continuously variable transmission for bicycles and other vehicles by reikiman » Thu, 10/08/2009 - 22:21 |
5 |
by aidanworthington Tue, 01/12/2010 - 14:16 |
|
|
What voltage/wattage combination for power assist at > 25km/h ? by khammo01 » Fri, 01/09/2009 - 09:24 |
5 |
by chas_stevenson Sat, 01/10/2009 - 11:27 |
|
|
Drill motors? by huntercook » Mon, 02/18/2008 - 10:02 |
5 |
by markzoes Sun, 10/01/2017 - 10:10 |
|
|
How to read motor performance charts and graphs by Mik » Wed, 03/12/2008 - 05:36 |
5 |
by frodus Mon, 03/17/2008 - 09:20 |
|
|
90 degree motor 12v by airman90 » Sat, 05/05/2012 - 11:44 |
5 |
by MEroller Tue, 05/08/2012 - 14:40 |
|
|
UPDATE ------I rewound my first motor, it runs great. by paul scooter » Thu, 01/11/2007 - 08:10 |
5 |
by rgx Sun, 02/11/2007 - 19:05 |
|
|
Golden motor question by slbaker » Sat, 11/15/2008 - 21:44 |
5 |
by ooo Sat, 08/21/2010 - 02:29 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- Skyhawk 57
- wild4
- justinsmith07
- Juli76
- xovacharging
Support V is for Voltage
