Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Brush hub motor repair question by Scottmagic » Tue, 01/22/2008 - 01:19 |
1 |
by Fechter Tue, 01/22/2008 - 15:41 |
|
What motor Drives you? by tortuga0303 » Mon, 06/11/2007 - 06:13 |
1 |
by MB-1-E Mon, 06/11/2007 - 11:27 |
|
Chain sprocket motor to Belt Sprocket Motor? Can it be done? by leu4life » Mon, 04/26/2010 - 19:19 |
1 |
by reikiman Mon, 04/26/2010 - 20:23 |
|
new motors by tiberiusx » Sat, 09/12/2009 - 13:50 |
1 |
by tiberiusx Sat, 09/12/2009 - 14:50 |
|
Bit of help with the Kollmorgen... by LinkOfHyrule » Wed, 10/17/2007 - 16:09 |
1 |
by Fechter Thu, 10/18/2007 - 20:13 |
|
my bicycle brushed motor have a mistake.... by WINDSHIELD » Tue, 03/27/2007 - 02:49 |
1 |
by ILBCNU Tue, 03/27/2007 - 17:34 |
|
mount u-bolt by Jonas Winslo » Mon, 08/20/2012 - 13:55 |
1 |
by reikiman Tue, 08/21/2012 - 08:05 |
|
The most efficient Hub Motor by wheelie » Wed, 03/18/2009 - 20:25 |
1 |
by garygid Wed, 03/18/2009 - 23:23 |
|
how to test my motor? by visfor » Mon, 08/20/2007 - 07:49 |
1 |
by andrew Mon, 08/20/2007 - 09:51 |
|
Brushed DC Motor Dead-Short by Kevin_Glass » Wed, 06/17/2009 - 13:41 |
1 |
by james joule Fri, 08/21/2009 - 05:17 |
|
PI7800 011G3 Inverter from PowTran ?? by 37Dodge » Tue, 07/19/2011 - 17:38 |
1 |
by greendriv Sat, 08/06/2011 - 21:30 |
|
Help repairing GIO hub motor freewheel sprocket by carlos1984 » Tue, 08/15/2017 - 09:37 |
1 |
by carlos1984 Tue, 08/15/2017 - 09:40 |
|
Holding Brushes Back During Reassembly? by MarxNutz » Mon, 03/22/2010 - 17:54 |
1 |
by strawhistle Mon, 03/22/2010 - 19:00 |
|
What type of Motor? by fJones » Sun, 04/19/2009 - 02:59 |
1 |
by reikiman Sun, 04/19/2009 - 15:01 |
|
why can't you run two AC motors off the same controller? by masonsteele » Wed, 01/24/2007 - 21:28 |
1 |
by rgx Thu, 01/25/2007 - 12:00 |
|
How to put a dc speed control on my dc motor by topnotchone » Sat, 11/19/2011 - 13:02 |
1 |
by Spaceangel Tue, 02/07/2012 - 07:58 |
|
12 to 24 volts or more by e-volt » Tue, 12/02/2008 - 22:04 |
1 |
by colin9876 Fri, 01/09/2009 - 10:31 |
|
Recommended controller for Brushed Manta Etek? by captsomer » Fri, 01/02/2009 - 11:29 |
1 |
by ruprek Sat, 01/03/2009 - 04:30 |
|
looking for a tall, thin dv motor by pengyou » Tue, 09/09/2008 - 12:20 |
2 |
by icecube57 Fri, 09/12/2008 - 13:31 |
|
How to refurbish old motor. by Mr. Sander » Mon, 12/03/2007 - 14:05 |
2 |
by Mr. Sander Thu, 12/13/2007 - 14:27 |
|
Need 60v 2000w Brushed Motor recomendations. by psycotrip » Fri, 07/15/2011 - 22:01 |
2 |
by psycotrip Sat, 07/16/2011 - 14:07 |
|
Any experience w/ Kelly Hub Motors? by KAE » Tue, 06/23/2009 - 21:17 |
2 |
by Cruisin Sat, 07/18/2009 - 16:04 |
|
Help with custom build please!!!!!!! by wackytomtom » Thu, 01/21/2010 - 17:51 |
2 |
by wackytomtom Sun, 01/24/2010 - 09:32 |
|
Greenwit Geared Hub Motor by johnnullstream » Sun, 07/27/2008 - 12:13 |
2 |
by eremite Mon, 03/30/2009 - 08:30 |
|
Help with this ebike hub motor by carlos1984 » Wed, 09/22/2021 - 17:24 |
2 |
by carlos1984 Thu, 09/23/2021 - 06:48 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- xovacharging
- stuuno
- marce002
- Heiwarsot
- headsupcorporation