Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
newbie question re torque curves and top speed by gwynnus » Sat, 09/06/2008 - 05:30 |
1 |
by spinningmagnets Sat, 09/06/2008 - 19:32 |
|
|
my bicycle brushed motor have a mistake.... by WINDSHIELD » Tue, 03/27/2007 - 02:49 |
1 |
by ILBCNU Tue, 03/27/2007 - 17:34 |
|
|
Luyuan CS350 Rear Wheel Locked by Mr Garrison » Thu, 07/29/2010 - 11:27 |
1 |
by oniea Sat, 08/07/2010 - 14:52 |
|
|
Manta motor by tercero » Mon, 11/10/2008 - 05:06 |
1 |
by reikiman Mon, 11/10/2008 - 12:10 |
|
|
how to test my motor? by visfor » Mon, 08/20/2007 - 07:49 |
1 |
by andrew Mon, 08/20/2007 - 09:51 |
|
|
Burnt-out Currie BLDC controller by dermot » Wed, 01/20/2010 - 08:25 |
1 |
by jateureka2 Wed, 05/05/2010 - 15:16 |
|
|
PC controlled motor as a variable load ? by max2tall » Thu, 03/11/2010 - 04:10 |
1 |
by max2tall Fri, 03/12/2010 - 04:57 |
|
|
EVT 168 motor replacement vendor suggestion? by MelTepid » Sun, 07/27/2008 - 07:54 |
1 |
by reikiman Sun, 07/27/2008 - 08:19 |
|
|
What epoxy would you recommend for loose magnet repair? by Coyle » Wed, 09/12/2018 - 09:23 |
1 |
by Spaceangel Fri, 09/14/2018 - 19:45 |
|
|
new motors by tiberiusx » Sat, 09/12/2009 - 13:50 |
1 |
by tiberiusx Sat, 09/12/2009 - 14:50 |
|
|
Chain sprocket motor to Belt Sprocket Motor? Can it be done? by leu4life » Mon, 04/26/2010 - 19:19 |
1 |
by reikiman Mon, 04/26/2010 - 20:23 |
|
|
why can't you run two AC motors off the same controller? by masonsteele » Wed, 01/24/2007 - 21:28 |
1 |
by rgx Thu, 01/25/2007 - 12:00 |
|
|
crystal power, so to speak by JCinStaunton » Sat, 03/15/2008 - 22:26 |
1 |
by LinkOfHyrule Sun, 03/16/2008 - 07:54 |
|
|
mount u-bolt by Jonas Winslo » Mon, 08/20/2012 - 13:55 |
1 |
by reikiman Tue, 08/21/2012 - 08:05 |
|
|
LEM-170 vs. Etek by LinkOfHyrule » Tue, 10/30/2007 - 18:32 |
1 |
by bradbunyard Sun, 07/13/2008 - 02:30 |
|
|
wrong direction by miro13car » Wed, 04/11/2007 - 05:49 |
1 |
by Drunkskunk Wed, 04/11/2007 - 15:55 |
|
|
Brushed DC Motor Dead-Short by Kevin_Glass » Wed, 06/17/2009 - 13:41 |
1 |
by james joule Fri, 08/21/2009 - 05:17 |
|
|
PI7800 011G3 Inverter from PowTran ?? by 37Dodge » Tue, 07/19/2011 - 17:38 |
1 |
by greendriv Sat, 08/06/2011 - 21:30 |
|
|
Electric Trike by mygrumpy » Tue, 06/24/2008 - 04:39 |
1 |
by chas_stevenson Tue, 06/24/2008 - 13:44 |
|
|
Help repairing GIO hub motor freewheel sprocket by carlos1984 » Tue, 08/15/2017 - 09:37 |
1 |
by carlos1984 Tue, 08/15/2017 - 09:40 |
|
|
The most efficient Hub Motor by wheelie » Wed, 03/18/2009 - 20:25 |
1 |
by garygid Wed, 03/18/2009 - 23:23 |
|
|
HAS anyone ever run a PMG 132 in reverse direction at full voltage? by getadirtbike » Thu, 05/24/2007 - 15:57 |
1 |
by Patrick Fri, 06/15/2007 - 23:03 |
|
|
Holding Brushes Back During Reassembly? by MarxNutz » Mon, 03/22/2010 - 17:54 |
1 |
by strawhistle Mon, 03/22/2010 - 19:00 |
|
|
How to put a dc speed control on my dc motor by topnotchone » Sat, 11/19/2011 - 13:02 |
1 |
by Spaceangel Tue, 02/07/2012 - 07:58 |
|
|
12 to 24 volts or more by e-volt » Tue, 12/02/2008 - 22:04 |
1 |
by colin9876 Fri, 01/09/2009 - 10:31 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- Bengun
- Skyhawk 57
- wild4
- justinsmith07
- Juli76
Support V is for Voltage
