Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
15 Electric Motorcycle LEMCO Motors by reikiman » Wed, 07/23/2008 - 07:44 |
0 |
by reikiman Wed, 07/23/2008 - 07:44 |
|
|
Electric Cars | Electric Motorcycles ; Electric Mopeds. by Mike » Mon, 05/31/2010 - 04:56 |
0 |
by Mike Mon, 05/31/2010 - 04:56 |
|
|
DC Motor Selection by jambuch » Wed, 03/16/2011 - 07:18 |
0 |
by jambuch Wed, 03/16/2011 - 07:18 |
|
|
Anyone had any experience with Unite Hub Motors? by Gman » Fri, 06/22/2007 - 23:01 |
0 |
by Gman Fri, 06/22/2007 - 23:01 |
|
|
Currie Direct Drive by rkd718 » Fri, 05/16/2008 - 17:21 |
0 |
by rkd718 Fri, 05/16/2008 - 17:21 |
|
|
How do I lay my mits on a Crystalyte motor and controller in Australia?? by wheelie » Sat, 11/15/2008 - 18:32 |
0 |
by wheelie Sat, 11/15/2008 - 18:32 |
|
|
motor identification by dingobingo » Wed, 10/17/2007 - 08:24 |
0 |
by dingobingo Wed, 10/17/2007 - 08:24 |
|
|
Brushed motors wear down the battery??? by reikiman » Sun, 03/29/2009 - 16:28 |
0 |
by reikiman Sun, 03/29/2009 - 16:28 |
|
|
Small Brushless Motors for a Scooter by Jason50153 » Wed, 07/21/2010 - 14:58 |
0 |
by Jason50153 Wed, 07/21/2010 - 14:58 |
|
|
Question for motor experts by Qmavam » Sun, 09/28/2008 - 07:42 |
0 |
by Qmavam Sun, 09/28/2008 - 07:42 |
|
|
Bmc 400w/600w 24v motor (USPD, lashout, Currie, Synergy cycles) by Pacific Ave Cycles » Wed, 03/03/2010 - 00:05 |
0 |
by Pacific Ave Cycles Wed, 03/03/2010 - 00:05 |
|
|
I need a 12.5inch Brushless Hub Motor. Suggestions? by Tireiron55 » Wed, 08/27/2008 - 09:34 |
0 |
by Tireiron55 Wed, 08/27/2008 - 09:34 |
|
|
Double Shaft Motor for electric skateboard by lehula » Mon, 05/11/2009 - 17:11 |
0 |
by lehula Mon, 05/11/2009 - 17:11 |
|
|
Where to buy BMC motors? by kwest » Thu, 03/11/2010 - 14:49 |
0 |
by kwest Thu, 03/11/2010 - 14:49 |
|
|
Drop in power output? by helix » Mon, 09/01/2008 - 11:30 |
0 |
by helix Mon, 09/01/2008 - 11:30 |
|
|
Electric Hubcap Pancake Motor, Controller, Workshops by Craig C » Wed, 09/15/2010 - 18:48 |
0 |
by Craig C Wed, 09/15/2010 - 18:48 |
|
|
can you run a perm 132 at 96 volts? by 96vperm132 » Wed, 04/16/2008 - 09:34 |
0 |
by 96vperm132 Wed, 04/16/2008 - 11:52 |
|
|
Homemede variable reluctance motor. Also the 12 volt bike to end all 12 volt bikes by D-Skor » Sat, 11/19/2011 - 07:11 |
0 |
by D-Skor Sat, 11/19/2011 - 07:11 |
|
|
Opening and cleaning an EVT hub motor by reikiman » Sat, 01/13/2007 - 23:17 |
0 |
by reikiman Sat, 01/13/2007 - 23:17 |
|
|
Motor Wiring Error, Popped controller by Qmavam » Fri, 10/24/2008 - 09:28 |
0 |
by Qmavam Fri, 10/24/2008 - 09:28 |
|
|
Kollmorgen Hub Question by engr_scotty » Tue, 07/15/2008 - 16:59 |
0 |
by engr_scotty Tue, 07/15/2008 - 16:59 |
|
|
BMC Thunderbolt 600W ... by vja4Him » Wed, 11/12/2008 - 17:27 |
0 |
by vja4Him Wed, 11/12/2008 - 17:27 |
|
|
Motor dimensions and other requirements... by carthikv12 » Sat, 08/01/2009 - 07:42 |
0 |
by carthikv12 Sat, 08/01/2009 - 07:42 |
|
|
Reversing direction of rotation of PMG 132 motors by FastForward » Thu, 05/29/2008 - 12:54 |
0 |
by FastForward Thu, 05/29/2008 - 12:54 |
|
|
Help! I can't find a sprocket to fit my Kollmorgen 400W BDC motor!! by Private Nukem » Tue, 11/18/2008 - 21:57 |
0 |
by Private Nukem Wed, 11/19/2008 - 06:51 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- 3DRoboGuy
- bcinsurance
- hineceg
- buzz86us
- baronwill469
Support V is for Voltage
