Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
How do you tell how much you need to charge ur battery for ur motor taking out? by Ausi319 » Thu, 10/23/2008 - 14:08 |
8 |
by Ausi319 Sat, 10/25/2008 - 21:02 |
|
how does 24v 4-wire reversible motor work? by gatorsby7 » Tue, 11/01/2011 - 10:24 |
2 |
by Pinche Thu, 06/28/2018 - 14:47 |
|
How does a brush DC motor stop? by noobster » Thu, 10/16/2008 - 03:46 |
3 |
by spinningmagnets Thu, 10/16/2008 - 20:34 |
|
How fast? at what gear ratio? here's how- by chas_stevenson » Sat, 01/13/2007 - 18:16 |
1 |
by chas_stevenson Sun, 01/14/2007 - 17:05 |
|
How much can I get from ....? by longtong3 » Mon, 01/28/2008 - 21:57 |
2 |
by longtong3 Tue, 01/29/2008 - 01:22 |
|
How to open a crystal hub motor by chas_stevenson » Sat, 01/13/2007 - 17:48 |
4 |
by Ypedal Mon, 01/15/2007 - 17:41 |
|
How to put a dc speed control on my dc motor by topnotchone » Sat, 11/19/2011 - 13:02 |
1 |
by Spaceangel Tue, 02/07/2012 - 07:58 |
|
How to read motor performance charts and graphs by Mik » Wed, 03/12/2008 - 05:36 |
5 |
by frodus Mon, 03/17/2008 - 09:20 |
|
How to refurbish old motor. by Mr. Sander » Mon, 12/03/2007 - 14:05 |
2 |
by Mr. Sander Thu, 12/13/2007 - 14:27 |
|
how to test my motor? by visfor » Mon, 08/20/2007 - 07:49 |
1 |
by andrew Mon, 08/20/2007 - 09:51 |
|
HTD 5m steel pulley. by edirtbiker » Tue, 06/12/2007 - 11:20 |
13 |
by chas_stevenson Fri, 06/15/2007 - 16:58 |
|
hub motor - not connecting hall leads by colin9876 » Thu, 01/22/2009 - 09:20 |
4 |
by colin9876 Wed, 01/28/2009 - 09:56 |
|
Hub Motor vs. Frame-mounted Motor with Chain Drive by xring » Wed, 07/09/2008 - 10:12 |
3 |
by LinkOfHyrule Wed, 07/09/2008 - 15:21 |
|
Hub motor wire polarity by jimmy » Mon, 02/02/2009 - 15:34 |
1 |
by dogman Mon, 02/02/2009 - 16:18 |
|
Hub motor/generator by bizybily » Sat, 01/31/2009 - 06:20 |
12 |
by bizybily Wed, 03/31/2010 - 04:38 |
|
I need a 12.5inch Brushless Hub Motor. Suggestions? by Tireiron55 » Wed, 08/27/2008 - 09:34 |
0 |
by Tireiron55 Wed, 08/27/2008 - 09:34 |
|
I need clarification re the sensor wires on a brushless DC motor and how to test them. by sapo » Fri, 04/23/2010 - 23:23 |
5 |
by sapo Mon, 04/26/2010 - 01:03 |
|
Idea for Motor intergrated into Bike Cranks by 7circle » Fri, 01/04/2008 - 11:15 |
7 |
by 7circle Sun, 01/06/2008 - 05:25 |
|
Is there a good replacement controller for Kollmorgen motors? by Lance » Wed, 11/11/2009 - 23:03 |
0 |
by Lance Wed, 11/11/2009 - 23:03 |
|
Kollmorgen 400w wiring by meatball » Sun, 10/14/2007 - 21:00 |
7 |
by Saeed Tue, 08/05/2008 - 06:31 |
|
Kollmorgen Hub Question by engr_scotty » Tue, 07/15/2008 - 16:59 |
0 |
by engr_scotty Tue, 07/15/2008 - 16:59 |
|
Kollmorgen undervoltage cutoff? and how to bypass it? by ejonesss » Thu, 05/15/2008 - 03:24 |
2 |
by ejonesss Sun, 05/18/2008 - 04:38 |
|
LEM-170 vs. Etek by LinkOfHyrule » Tue, 10/30/2007 - 18:32 |
1 |
by bradbunyard Sun, 07/13/2008 - 02:30 |
|
ligthest regenerating hub motor by Efried » Wed, 12/26/2007 - 07:50 |
0 |
by Efried Tue, 01/22/2008 - 15:41 |
|
Linear actuator motor by countersunk » Mon, 02/15/2010 - 23:02 |
4 |
by countersunk Fri, 02/19/2010 - 00:57 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- Juli76
- xovacharging
- stuuno
- marce002
- Heiwarsot