Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
12 to 24 volts or more by e-volt » Tue, 12/02/2008 - 22:04 |
1 |
by colin9876 Fri, 01/09/2009 - 10:31 |
|
Opening and cleaning an EVT hub motor by reikiman » Sat, 01/13/2007 - 23:17 |
0 |
by reikiman Sat, 01/13/2007 - 23:17 |
|
Bmc 400w/600w 24v motor (USPD, lashout, Currie, Synergy cycles) by Pacific Ave Cycles » Wed, 03/03/2010 - 00:05 |
0 |
by Pacific Ave Cycles Wed, 03/03/2010 - 00:05 |
|
How much can I get from ....? by longtong3 » Mon, 01/28/2008 - 21:57 |
2 |
by longtong3 Tue, 01/29/2008 - 01:22 |
|
Help repairing GIO hub motor freewheel sprocket by carlos1984 » Tue, 08/15/2017 - 09:37 |
1 |
by carlos1984 Tue, 08/15/2017 - 09:40 |
|
SOUPCAN MOTOR, 98% Efficient by SPARKY » Thu, 08/21/2008 - 12:26 |
2 |
by SPARKY Fri, 08/22/2008 - 12:13 |
|
I need a 12.5inch Brushless Hub Motor. Suggestions? by Tireiron55 » Wed, 08/27/2008 - 09:34 |
0 |
by Tireiron55 Wed, 08/27/2008 - 09:34 |
|
Double Shaft Motor for electric skateboard by lehula » Mon, 05/11/2009 - 17:11 |
0 |
by lehula Mon, 05/11/2009 - 17:11 |
|
Bionx wheel hub by sandorszabo » Tue, 06/19/2007 - 13:44 |
2 |
by Aquinas Hub Sun, 06/24/2007 - 20:51 |
|
Kollmorgen undervoltage cutoff? and how to bypass it? by ejonesss » Thu, 05/15/2008 - 03:24 |
2 |
by ejonesss Sun, 05/18/2008 - 04:38 |
|
Fast analytical program for custom motor development by gorazd » Tue, 09/07/2010 - 04:13 |
0 |
by gorazd Tue, 09/07/2010 - 04:13 |
|
Mars brushless wiring question by ruprek » Mon, 10/06/2008 - 06:26 |
3 |
by reikiman Mon, 10/06/2008 - 18:22 |
|
with or without a controller by tiberiusx » Wed, 09/30/2009 - 11:36 |
2 |
by tiberiusx Tue, 10/06/2009 - 12:03 |
|
Required vs Available Torque spreadsheet by jdh2550_1 » Tue, 10/16/2007 - 17:45 |
3 |
by echuckj5 Tue, 10/16/2007 - 19:56 |
|
how does 24v 4-wire reversible motor work? by gatorsby7 » Tue, 11/01/2011 - 10:24 |
2 |
by Pinche Thu, 06/28/2018 - 14:47 |
|
Recommended controller for Brushed Manta Etek? by captsomer » Fri, 01/02/2009 - 11:29 |
1 |
by ruprek Sat, 01/03/2009 - 04:30 |
|
Etek back!? by andrew » Tue, 02/06/2007 - 15:56 |
3 |
by NickF23 Fri, 05/25/2007 - 12:38 |
|
D.I.Y Gearbox by Mr. Sander » Wed, 02/20/2008 - 12:54 |
2 |
by andrew Sat, 02/23/2008 - 12:15 |
|
Holding Brushes Back During Reassembly? by MarxNutz » Mon, 03/22/2010 - 17:54 |
1 |
by strawhistle Mon, 03/22/2010 - 19:00 |
|
I need clarification re the sensor wires on a brushless DC motor and how to test them. by sapo » Fri, 04/23/2010 - 23:23 |
5 |
by sapo Mon, 04/26/2010 - 01:03 |
|
Drop in power output? by helix » Mon, 09/01/2008 - 11:30 |
0 |
by helix Mon, 09/01/2008 - 11:30 |
|
Looking for replacement brushes by mf70 » Mon, 06/01/2009 - 09:54 |
3 |
by mf70 Thu, 07/02/2009 - 10:39 |
|
Rotoverter 94+ efficiency by tortuga0303 » Tue, 06/26/2007 - 14:07 |
1 |
by Gman Wed, 06/27/2007 - 21:55 |
|
Reversing direction of rotation of PMG 132 motors by FastForward » Thu, 05/29/2008 - 12:54 |
0 |
by FastForward Thu, 05/29/2008 - 12:54 |
|
Motorcycle Hub/Wheel Motor Suggestions? by OdnsRvns » Sat, 09/18/2010 - 23:14 |
5 |
by reikiman Mon, 09/20/2010 - 18:33 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- Skyhawk 57
- wild4
- justinsmith07
- Juli76
- xovacharging