Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Direct wheel mount to a Brushless Etek Motor by moonfresh » Tue, 08/19/2008 - 23:08 |
1 |
by LinkOfHyrule Wed, 08/20/2008 - 05:31 |
|
HAS anyone ever run a PMG 132 in reverse direction at full voltage? by getadirtbike » Thu, 05/24/2007 - 15:57 |
1 |
by Patrick Fri, 06/15/2007 - 23:03 |
|
PC controlled motor as a variable load ? by max2tall » Thu, 03/11/2010 - 04:10 |
1 |
by max2tall Fri, 03/12/2010 - 04:57 |
|
a/c to d/c conversion by Gramps » Sat, 10/04/2008 - 10:30 |
1 |
by reikiman Sat, 10/04/2008 - 12:52 |
|
What epoxy would you recommend for loose magnet repair? by Coyle » Wed, 09/12/2018 - 09:23 |
1 |
by Spaceangel Fri, 09/14/2018 - 19:45 |
|
Luyuan CS350 Rear Wheel Locked by Mr Garrison » Thu, 07/29/2010 - 11:27 |
1 |
by oniea Sat, 08/07/2010 - 14:52 |
|
Chain sprocket motor to Belt Sprocket Motor? Can it be done? by leu4life » Mon, 04/26/2010 - 19:19 |
1 |
by reikiman Mon, 04/26/2010 - 20:23 |
|
newbie question re torque curves and top speed by gwynnus » Sat, 09/06/2008 - 05:30 |
1 |
by spinningmagnets Sat, 09/06/2008 - 19:32 |
|
Rotoverter 94+ efficiency by tortuga0303 » Tue, 06/26/2007 - 14:07 |
1 |
by Gman Wed, 06/27/2007 - 21:55 |
|
Manta motor by tercero » Mon, 11/10/2008 - 05:06 |
1 |
by reikiman Mon, 11/10/2008 - 12:10 |
|
OT: thinking of selling motors by Leeps » Thu, 11/30/2006 - 11:53 |
1 |
by Sturdly Thu, 11/30/2006 - 16:22 |
|
Burnt-out Currie BLDC controller by dermot » Wed, 01/20/2010 - 08:25 |
1 |
by jateureka2 Wed, 05/05/2010 - 15:16 |
|
Can anyone help me find/measure/calculate the field inductance of an Elec-Trak Motor? by racermike39 » Thu, 11/29/2007 - 16:58 |
1 |
by rgx Fri, 11/30/2007 - 10:18 |
|
EVT 168 motor replacement vendor suggestion? by MelTepid » Sun, 07/27/2008 - 07:54 |
1 |
by reikiman Sun, 07/27/2008 - 08:19 |
|
mount u-bolt by Jonas Winslo » Mon, 08/20/2012 - 13:55 |
1 |
by reikiman Tue, 08/21/2012 - 08:05 |
|
Crystalyte motors by Arnold » Thu, 05/17/2007 - 20:17 |
1 |
by Drunkskunk Fri, 05/18/2007 - 10:15 |
|
Help repairing GIO hub motor freewheel sprocket by carlos1984 » Tue, 08/15/2017 - 09:37 |
1 |
by carlos1984 Tue, 08/15/2017 - 09:40 |
|
new motors by tiberiusx » Sat, 09/12/2009 - 13:50 |
1 |
by tiberiusx Sat, 09/12/2009 - 14:50 |
|
How fast? at what gear ratio? here's how- by chas_stevenson » Sat, 01/13/2007 - 18:16 |
1 |
by chas_stevenson Sun, 01/14/2007 - 17:05 |
|
Brush hub motor repair question by Scottmagic » Tue, 01/22/2008 - 01:19 |
1 |
by Fechter Tue, 01/22/2008 - 15:41 |
|
PI7800 011G3 Inverter from PowTran ?? by 37Dodge » Tue, 07/19/2011 - 17:38 |
1 |
by greendriv Sat, 08/06/2011 - 21:30 |
|
What motor Drives you? by tortuga0303 » Mon, 06/11/2007 - 06:13 |
1 |
by MB-1-E Mon, 06/11/2007 - 11:27 |
|
Holding Brushes Back During Reassembly? by MarxNutz » Mon, 03/22/2010 - 17:54 |
1 |
by strawhistle Mon, 03/22/2010 - 19:00 |
|
Bit of help with the Kollmorgen... by LinkOfHyrule » Wed, 10/17/2007 - 16:09 |
1 |
by Fechter Thu, 10/18/2007 - 20:13 |
|
How to put a dc speed control on my dc motor by topnotchone » Sat, 11/19/2011 - 13:02 |
1 |
by Spaceangel Tue, 02/07/2012 - 07:58 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- Persival
- boomingheight
- janet
- Bengun
- Skyhawk 57