Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Bmc 400w/600w 24v motor (USPD, lashout, Currie, Synergy cycles) by Pacific Ave Cycles » Wed, 03/03/2010 - 00:05 |
4 |
by friedwires Tue, 04/13/2010 - 18:49 |
|
Bmc 400w/600w 24v motor (USPD, lashout, Currie, Synergy cycles) by Pacific Ave Cycles » Wed, 03/03/2010 - 00:05 |
0 |
by Pacific Ave Cycles Wed, 03/03/2010 - 00:05 |
|
BMC Thunderbolt 600W ... by vja4Him » Wed, 11/12/2008 - 17:27 |
0 |
by vja4Him Wed, 11/12/2008 - 17:27 |
|
Brush hub motor repair question by Scottmagic » Tue, 01/22/2008 - 01:19 |
1 |
by Fechter Tue, 01/22/2008 - 15:41 |
|
Brushed DC Motor Dead-Short by Kevin_Glass » Wed, 06/17/2009 - 13:41 |
1 |
by james joule Fri, 08/21/2009 - 05:17 |
|
Brushed motors wear down the battery??? by reikiman » Sun, 03/29/2009 - 16:28 |
0 |
by reikiman Sun, 03/29/2009 - 16:28 |
|
Brushed or Bushless by wavedog » Mon, 09/29/2008 - 20:05 |
3 |
by wavedog Tue, 09/30/2008 - 08:26 |
|
Brushless motor questions by mech701 » Sat, 08/16/2008 - 14:18 |
12 |
by mech701 Sun, 09/28/2008 - 07:40 |
|
Brushless Motors 10-20KW and 40N.m. max Torque by FastForward » Mon, 06/23/2008 - 17:32 |
3 |
by LinkOfHyrule Tue, 06/24/2008 - 13:19 |
|
Brushless Rewiring by abudabit » Mon, 10/06/2008 - 11:26 |
6 |
by abudabit Thu, 10/09/2008 - 09:28 |
|
Burnt-out Currie BLDC controller by dermot » Wed, 01/20/2010 - 08:25 |
1 |
by jateureka2 Wed, 05/05/2010 - 15:16 |
|
Can anyone help me find/measure/calculate the field inductance of an Elec-Trak Motor? by racermike39 » Thu, 11/29/2007 - 16:58 |
1 |
by rgx Fri, 11/30/2007 - 10:18 |
|
Can I hot wire directly to see if the motor is good? by 2 B theprince » Thu, 08/28/2008 - 08:52 |
4 |
by 2 B theprince Thu, 08/28/2008 - 14:10 |
|
Can someone point me to a primer on motors? by pengyou » Mon, 06/18/2007 - 06:45 |
17 |
by Stleride Fri, 10/30/2015 - 16:37 |
|
can you run a perm 132 at 96 volts? by 96vperm132 » Wed, 04/16/2008 - 09:34 |
0 |
by 96vperm132 Wed, 04/16/2008 - 11:52 |
|
Chain sprocket motor to Belt Sprocket Motor? Can it be done? by leu4life » Mon, 04/26/2010 - 19:19 |
1 |
by reikiman Mon, 04/26/2010 - 20:23 |
|
Converting a generator to a motor by motorbiketim » Fri, 05/09/2008 - 13:52 |
5 |
by motorbiketim Sun, 05/11/2008 - 15:42 |
|
Converting Veteran Car Generator from 6Volts to 12 Volts by gavret » Sun, 07/06/2008 - 21:07 |
0 |
by gavret Sun, 07/06/2008 - 21:07 |
|
crystal power, so to speak by JCinStaunton » Sat, 03/15/2008 - 22:26 |
1 |
by LinkOfHyrule Sun, 03/16/2008 - 07:54 |
|
Crystalyte 409 on 66v by magudaman » Tue, 03/27/2007 - 17:46 |
21 |
by magudaman Sat, 10/31/2015 - 22:31 |
|
Crystalyte motors by Arnold » Thu, 05/17/2007 - 20:17 |
1 |
by Drunkskunk Fri, 05/18/2007 - 10:15 |
|
Currie Direct Drive by rkd718 » Fri, 05/16/2008 - 17:21 |
0 |
by rkd718 Fri, 05/16/2008 - 17:21 |
|
Currie Electro Drive 1000W Motor question by Newt » Sun, 02/19/2012 - 19:16 |
0 |
by Newt Sun, 02/19/2012 - 19:16 |
|
Currie GT300, more torque and more power? by iflymyhelishigh » Tue, 04/07/2009 - 17:17 |
0 |
by iflymyhelishigh Tue, 04/07/2009 - 17:17 |
|
D.I.Y Gearbox by Mr. Sander » Wed, 02/20/2008 - 12:54 |
2 |
by andrew Sat, 02/23/2008 - 12:15 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- Persival
- boomingheight
- janet
- Bengun
- Skyhawk 57