Magic Sequences for Vectrix Service

Mik's picture
Submitted by Mik on Tue, 03/15/2011 - 02:39

This page can be used to list the magic sequences that make a Vectrix VX-1 do certain things.
.

Here are the ones I remember off the top of my head - could anyone who has recently used them write exactly how it works, please?

I'll edit this first post so the best descriptions are added to the first post to make it more user-friendly.

.

Turning on both head-light filaments at once:

Turning off the head-light (different with different software versions):
---------------------------------------------------------------------------------------------------------------------------------
Motor encoder calibration:
With rear wheel lifted off the ground and side stand in the "up" position:
Before you turn on the key, apply full throttle and the right brake lever. Turn on key and hold throttle and brake until wrench icon appears. The encoder routine will start automatically. First the wheel will lock to a position then it will slowly turn until it is calibrated.
See: http://visforvoltage.org/forum/9644-encoder-calibration-routine
---------------------------------------------------------------------------------------------------------------------------------

Motor phase test:
With rear wheel lifted off the ground and side stand in the "up" position:
Before you turn on the key, apply full throttle and the left brake lever. Turn on key and hold throttle and brake until wrench icon appears. The motor (wheel) should spin forward slowly and smoothly. This tests the phases of the MC w/o any encoder feedback.

See: http://visforvoltage.org/forum/10108-vectrix-not-running-right#comment-55531
---------------------------------------------------------------------------------------------------------------------------------
Checking battery temperature (different with different software versions):

Checking battery voltage (different with different software versions):
---------------------------------------------------------------------------------------------------------------------------------


Throttle Calibration

See... http://visforvoltage.org/forum/4918-throttle-calibration-indicator

Bike ignition On
Kill Switch Off
Pull left brake lever
Speedo should read 43kph
If not, adjust as per linked instructions.

MW

.

I doubt we know them all yet, so please reply if you know any other magic sequences.

Topics: 
Vectrix Collaborative Handbook

Comments

Submitted by ofx210p on Mon, 07/04/2011 - 01:50.

Have these been written down anywhere ?

Mik's picture

Submitted by Mik on Mon, 07/04/2011 - 14:48.

Have these been written down anywhere ?

Yes, those have been mentioned somewhere on the VisforVoltage Vectrix pages before, but it needs some searching to find them. Then, they could be collected here in this thread in one easy to find place.

This information may be used entirely at your own risk.

There is always a way if there is no other way!

Mik's picture

Submitted by Mik on Mon, 07/04/2011 - 21:26.

Have these been written down anywhere ?

I've added the procedures for encoder and phase test to the first post.

This information may be used entirely at your own risk.

There is always a way if there is no other way!

Submitted by martinwinlow on Tue, 09/11/2012 - 04:54.

Throttle Calibration

See... http://visforvoltage.org/forum/4918-throttle-calibration-indicator

Bike ignition On
Kill Switch Off
Pull left brake lever
Speedo should read 43kph
If not, adjust as per linked instructions.

MW

Regards, Martin Winlow
Isle of Colonsay, Scotland
evalbum.com/2092

Mik's picture

Submitted by Mik on Fri, 11/30/2012 - 17:36.

Thanks, MW, I have added it to the first post.

This information may be used entirely at your own risk.

There is always a way if there is no other way!

DanDiego's picture

Submitted by DanDiego on Sat, 04/19/2014 - 17:57.

I found a Vectrix VX-1 Service Manual here. You have to join to access the zip file.

http://websd-vectrixscenecom.webs.com/WEBPROTECT-filesmembersonly.htm

DanDiego

Submitted by Kocho on Sun, 04/20/2014 - 14:19.

No luck with that site - don't know if it is a scam or just not working, but after registering, it won't let me login and some pages don't load...

Submitted by martinwinlow on Mon, 04/21/2014 - 01:06.

I just tried it - I am a member already - and it works for me. The box at the bottom of the page is where the files can be clicked on to download. On my browser (Mac Safari), it initially looks blank, but if you hover your mouse over it, it populates with the files…

Screen Shot 2014-04-21 at 09.04.29.jpg

Perhaps you should try a different browser or maybe there is a delay in your registration being activated? MW

Regards, Martin Winlow
Isle of Colonsay, Scotland
evalbum.com/2092

Submitted by Kocho on Mon, 04/21/2014 - 06:01.

Mik,

Tried it with my "desktop" browser (Internet Explorer on Windows 8.1) today and it worked for some files. Downloaded the .hex files OK. Still does something wired and blocks my "metro" browser while the desktop is blocked trying to download the .rar file from that site...

Submitted by Kocho on Mon, 04/21/2014 - 06:10.

Worked for all files. I could not for some reason download the .rar file directly to my network share (the browser just hangs up, even though it is not the largest file there), but it worked to my desktop locally.

israndy's picture

Submitted by israndy on Tue, 07/14/2015 - 09:05.

I downloaded the software YEARS ago, but I finally BootCamped my Mac and when I transferred the files over it keeps giving me an error about needing to be re-installed. I fear it was because I unpacked the .rar on the Mac and threw the fie away. So I went to the linked website again and was greeted with this:

Screen Shot 2015-07-14 at 8.56.44 AM.png

I tried the same thing on the PC side. OK, so I will come back later...

... Well it's been a week and the server is still down. So anyone still have a copy of the installer?

-Randy

______________________
I also own a 2018 Tesla Model 3 and a 2012 Mitsubishi iMiev

Submitted by Syle3 on Mon, 03/21/2022 - 08:44.

Hello,

The link is dead.

May you still have a copy? I want to centralize all documentation there.

Thank you.

https://drive.google.com/drive/folders/1vY0CGKS0KtYSHri4-dY_4Yp82YVAFpgp?usp=sharing

Submitted by Syle3 on Mon, 03/21/2022 - 08:50.

While riding:

full beam then blinker = Both sides blinkers sometimes needs "slightly" left brake too.


Who's online

There are currently 0 users online.

Who's new

  • eric01
  • Norberto
  • sarim
  • Edd
  • OlaOst

Support V is for Voltage

Support V is for Voltage