Electric vehicle motors (DC motors, AC motors, hub motors, etc)
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Mars brushless wiring question by ruprek » Mon, 10/06/2008 - 06:26 |
3 |
by reikiman Mon, 10/06/2008 - 18:22 |
|
|
a/c to d/c conversion by Gramps » Sat, 10/04/2008 - 10:30 |
1 |
by reikiman Sat, 10/04/2008 - 12:52 |
|
|
Please HELP an ignorant chick with this electric crap! - Unite 24V motor = custom e-bike mess! (Page: 1, 2, 3)
by puppetplanet » Fri, 09/12/2008 - 08:13 |
79 |
by puppetplanet Fri, 10/03/2008 - 18:17 |
|
|
mars brushless vs brushed etek for an electric dirt bike by kp647 » Fri, 09/05/2008 - 04:20 |
6 |
by ruprek Wed, 10/01/2008 - 21:14 |
|
|
BMC 3000 watt brushless motor by ruprek » Wed, 09/24/2008 - 02:21 |
1 |
by ruprek Wed, 10/01/2008 - 20:40 |
|
|
Brushed or Bushless by wavedog » Mon, 09/29/2008 - 20:05 |
3 |
by wavedog Tue, 09/30/2008 - 08:26 |
|
|
Question for motor experts by Qmavam » Sun, 09/28/2008 - 07:42 |
0 |
by Qmavam Sun, 09/28/2008 - 07:42 |
|
|
Brushless motor questions by mech701 » Sat, 08/16/2008 - 14:18 |
12 |
by mech701 Sun, 09/28/2008 - 07:40 |
|
|
Motor voltage vs amps vs watts by drlizardo » Sun, 09/21/2008 - 10:02 |
4 |
by deronmoped Sun, 09/21/2008 - 22:38 |
|
|
Speed vs. Torque by jdh2550_1 » Sun, 09/21/2008 - 10:16 |
3 |
by jdh2550_1 Sun, 09/21/2008 - 11:14 |
|
|
Heinzmann 24v hub in need of service/repair by Ian » Mon, 09/15/2008 - 17:39 |
1 |
by deronmoped Mon, 09/15/2008 - 23:34 |
|
|
looking for a tall, thin dv motor by pengyou » Tue, 09/09/2008 - 12:20 |
2 |
by icecube57 Fri, 09/12/2008 - 13:31 |
|
|
newbie question re torque curves and top speed by gwynnus » Sat, 09/06/2008 - 05:30 |
1 |
by spinningmagnets Sat, 09/06/2008 - 19:32 |
|
|
Drop in power output? by helix » Mon, 09/01/2008 - 11:30 |
0 |
by helix Mon, 09/01/2008 - 11:30 |
|
|
Alternator Output Question by Rane » Thu, 08/28/2008 - 22:55 |
4 |
by LinkOfHyrule Fri, 08/29/2008 - 23:05 |
|
|
Can I hot wire directly to see if the motor is good? by 2 B theprince » Thu, 08/28/2008 - 08:52 |
4 |
by 2 B theprince Thu, 08/28/2008 - 14:10 |
|
|
Mars Brushless PMAC electric motor: 48 volt max or 72 volt max??? by formicafowl » Sun, 08/24/2008 - 18:14 |
2 |
by formicafowl Wed, 08/27/2008 - 14:29 |
|
|
I need a 12.5inch Brushless Hub Motor. Suggestions? by Tireiron55 » Wed, 08/27/2008 - 09:34 |
0 |
by Tireiron55 Wed, 08/27/2008 - 09:34 |
|
|
what is an etek brush card assembly by sawracer » Thu, 08/21/2008 - 17:43 |
2 |
by sawracer Fri, 08/22/2008 - 17:46 |
|
|
SOUPCAN MOTOR, 98% Efficient by SPARKY » Thu, 08/21/2008 - 12:26 |
2 |
by SPARKY Fri, 08/22/2008 - 12:13 |
|
|
Direct wheel mount to a Brushless Etek Motor by moonfresh » Tue, 08/19/2008 - 23:08 |
1 |
by LinkOfHyrule Wed, 08/20/2008 - 05:31 |
|
|
Kollmorgen 400w wiring by meatball » Sun, 10/14/2007 - 21:00 |
7 |
by Saeed Tue, 08/05/2008 - 06:31 |
|
|
etek by echuckj5 » Mon, 09/10/2007 - 19:15 |
7 |
by echuckj5 Wed, 07/30/2008 - 09:17 |
|
|
Wire size for 1200W? by mf70 » Fri, 03/21/2008 - 12:14 |
7 |
by LinkOfHyrule Wed, 07/30/2008 - 09:04 |
|
|
EVT 168 motor replacement vendor suggestion? by MelTepid » Sun, 07/27/2008 - 07:54 |
1 |
by reikiman Sun, 07/27/2008 - 08:19 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- eric01
- Norberto
- sarim
- Edd
- OlaOst
Support V is for Voltage
