Electric vehicle controllers and control systems
Log in to post new content in the forum.
| Topic / Topic starter | Replies | Last post | |
|---|---|---|---|
|
Sabertooth motor driver, but brushless? by ragonamuffin » Sun, 08/07/2011 - 14:58 |
0 |
by ragonamuffin Sun, 08/07/2011 - 14:58 |
|
|
Orphaned by Powerpackmotors, Ruprek needs help matching Kelly brushless controller to Tim's 1500 watt brushless motor. by ruprek » Sat, 08/09/2008 - 04:39 |
2 |
by electricLarry Sun, 08/10/2008 - 08:50 |
|
|
Thoughts about a crash/impact circuit breaker? by Martijn » Thu, 09/03/2009 - 09:14 |
4 |
by Martijn Fri, 09/04/2009 - 03:14 |
|
|
controller for BLDC or PMAC motors...? by masonsteele » Mon, 04/23/2007 - 16:41 |
9 |
by frodus Mon, 03/17/2008 - 08:48 |
|
|
Vectrix-style Twist Grip Throttle / R-Brake by wanders » Wed, 04/02/2008 - 07:52 |
5 |
by Patriot Tue, 08/05/2008 - 23:06 |
|
|
Accelerated Systems Inc. Introduces New Line of BAC Electric Motor Controllers at the Taipei Cycle Show 2012 by reikiman » Tue, 02/21/2012 - 10:44 |
3 |
by ASI guy Fri, 03/09/2012 - 08:39 |
|
|
Increase speed by zelakane » Mon, 06/04/2012 - 10:35 |
0 |
by zelakane Mon, 06/04/2012 - 10:35 |
|
|
Help with Thumb throttle and wire mess by colin9876 » Fri, 01/16/2009 - 23:17 |
0 |
by colin9876 Fri, 01/16/2009 - 23:17 |
|
|
Crystalyte Cruise Control with Cyclone (Headline) Controller on electric bike--how can I do it? by PJIII » Sat, 03/27/2010 - 19:53 |
1 |
by diverdon Sat, 04/02/2022 - 12:24 |
|
|
Electric Bike Hub Motor - How to Replace a Hall-effect Sensor by Gman » Tue, 08/21/2007 - 03:43 |
1 |
by sapo Thu, 08/26/2010 - 13:09 |
|
|
Two hub motors, one controller?? by Tony Munn » Fri, 08/01/2008 - 18:00 |
6 |
by sparc5 Thu, 03/05/2009 - 19:37 |
|
|
Boost converter 3.3v to 36V?? by colin9876 » Tue, 04/12/2011 - 14:55 |
6 |
by colin9876 Fri, 04/15/2011 - 23:26 |
|
|
LM-339 based controllers, etc by cnagorka » Thu, 05/28/2009 - 17:01 |
1 |
by reikiman Thu, 05/28/2009 - 20:43 |
|
|
Need advise on 24v controller by tesco » Wed, 01/17/2007 - 06:47 |
2 |
by reikiman Thu, 02/01/2007 - 14:23 |
|
|
new electric board build, need help with using an rc car throttle controller. by electric board1 » Tue, 11/16/2010 - 10:21 |
0 |
by electric board1 Tue, 11/16/2010 - 10:21 |
|
|
How do I determine which controller to use by hendu » Thu, 01/24/2008 - 07:27 |
4 |
by hendu Wed, 02/06/2008 - 07:42 |
|
|
China KU63 motor controller circuit (reengineered) by avandalen » Mon, 08/29/2011 - 00:53 |
0 |
by avandalen Mon, 08/29/2011 - 00:53 |
|
|
Where to Buy? Solenoid, Pot box. by Qmavam » Fri, 08/22/2008 - 06:15 |
1 |
by reikiman Fri, 08/22/2008 - 07:13 |
|
|
motor runs backwards by gilnetwisc » Tue, 09/15/2009 - 12:08 |
7 |
by gilnetwisc Sat, 09/26/2009 - 19:18 |
|
|
A new custom EVT 4000 controller by saskrick » Tue, 05/08/2007 - 10:21 |
26 |
by Dean b Fri, 03/17/2017 - 18:14 |
|
|
cut-off switch question by knurn » Fri, 05/09/2008 - 09:55 |
0 |
by knurn Fri, 05/09/2008 - 09:55 |
|
|
Contactor with Emergency mode BUT no wasted coil Power by Jeffkay » Sat, 05/24/2008 - 20:24 |
1 |
by ArcticFox Sat, 05/24/2008 - 22:09 |
|
|
Curtis Programming Station 1314PC-4401 $435.00 by Cruisin » Tue, 08/21/2012 - 10:23 |
0 |
by Cruisin Tue, 08/21/2012 - 10:23 |
|
|
Using 48 volts battery pack with 24 volt controller. by evDreamer » Mon, 03/02/2009 - 16:33 |
8 |
by antiscab Tue, 03/03/2009 - 17:05 |
|
|
Contactor vs SCR by BM1 » Thu, 04/08/2010 - 08:17 |
3 |
by BM1 Thu, 04/08/2010 - 19:28 |
Log in to post new content in the forum.
Who's online
There are currently 0 users online.
Who's new
- Bengun
- Skyhawk 57
- wild4
- justinsmith07
- Juli76
Support V is for Voltage
